RAK811-N can't join GW

  • Ah, and it might be a good idea to set the channel mask if you only got a single channel GW:
    at+set_config=mask:0,0001 for channel 0 or
    at+set_config=mask:0,0002 for channel 1

    But as I said, I got no experience with singel channel GWs... maybe I should order one, just for education :tongue:

  • at+reload : nothing better

    what is the command to set "channel1, 868.300MHz" ?
    i try the mask at+set_config=mask:0,0002
    but i receive ERROR-1

    .. but in fact... wich channel is available on this GW !?...
    need to have a look in the arduino code !

    i ordered this single channel GW just for my proof of concept prototype. i wish to rder a better one, but later !
    which one do you suggest ? one with a RPI3 + ??... but there a lot off possibility and i'm not sure which one to choose

  • I love! the RAK831, they got a very good performance. But the set Antenna is not too good. If you got some experience, I reccomend to build a groundplane or coco antenna. Else look for a good 868MHz antenna you can get. I got one fibre glass 868MHz from RAK, but I measured it to have a center frequency of 913MHz...

  • If you want, I can join with your settings to see if on TTN side, everything is ok.

  • hello,

    is that possible to create a second temporary user in TTN account ?
    there is not too much configuration in TTN account, so i suppose that all right.

    i have more doubt about the LoraGO GW configuration !

    what is the command to set "channel0, 868.100MHz" ?
    i try the mask at+set_config=mask:0,0001
    but i receive ERROR-1 ==> so what it the right mask to set up channel 0 please ?
    868.100 is the specified frequency in the arduino firmware, i set up before compiling and flash my GW.


  • Sorry, it's at+set_config=ch_mask:0,0001

  • not better :(

    i see the "join accept" :
    0_1525785637562_TTN GWtraffic 5.png

    but even the ERROR-6 just after the at+send command (ther is 20 seconds between the join and the send command, which is enough to see the join accept in the TTN page) !

    do you use a RAK811 or a RAK811-N (as me) ?


  • I use the RAK811, so I don't need an additional microcontroller

  • Do you have any other gateway in your region where you can go to and try to join your 811? Once joined, it stays joined.

  • no nearest GW is about 30km !

    well i plan to use RAK811 too withtout second CPU.. can you point me to a good tutorial to set up the right tool chain please ?

    well i will have a look to the arduino GW firmware .. but not so confident
    some users report that the RAK811-N fw is bugged .. some others say it's working ..

    if you have any idea please don't hesitate !

  • woaa !.. i just modify the setting order, set the keys juste before the join command and now i see that :
    0_1525790931333_TTN appdata3.png

    1/ where are my data ? ( at+send=1,1,010101 ) ?
    2/ i got even ERROR-6 message !
    3/ sometime between several send, i receive at+recv=3,0,0 :o)
    then a lot of ERROR-6 !!

    0_1525791098540_RAK811-N terminal.png

  • here it is some data :))))

    0_1525791208143_TTN appdata4.png

    but a lot of ERROR-6 between !

    i send too fast ? (20 seconds)

  • Hm, these MAC BUSY errors are really strange.
    I don't think you are sending too fast, as I sometimes send 5 messages in 2 seconds (after hard reboot, I send the device config of the irrigation sensors which is no problem at all). So i think RAK811-N are buggy somehow...
    As for developement, I'm afraid that the -N version might be the wrong choice. As you see on the following picture, there is no internal programming support:
    Taken form the Aliexpress RAK811-N page I found this on Aliexpress.

    As for the toolchain, I use GNU Arm Embedded Toolchain, at the moment without any IDE using Makefiles under Ubuntu. I simulate using qemu and I debug/programm the devices with a fake J-Link using OpenOCD.
    But I think I'll give GNU MCU Eclipse a try soon. But in the end, you know, I don't like this bloatware IDEs too much. What OS are you on?

    I try to provide a cleaned up template project for the RAK811 soon via github. To be honest, it's a big uncommented nearly -everything-in-one-file-mess at the moment, especially the low power states need some love.

  • i agree, RAK811-N is not the good choice for the prototype, but it is what i have in my hands right now to start my tests !

    well the link is realy unstable, i can't exchange data anymore !
    if i had not a screen copy, i won't believe that i already receive one time 3,0,0 !

    i'm working under Windows 99% of time

    i don't understand the paramters of the rx2 command :
    what is the datarate ? the datasheet say "see regions define", but in the table §5, i don't find it !??

  • Hm, I don't know which §5 you are referring to. The RX2 is defined in Section 2.2.7 in the LoRaWAN 1.1 Regional Parameters, at least for the EU868. It defaults to 869.525MHz/DR0. BUT: In EU868, the Network/Gateway may set another channel/DR for RX2 in the Join Accept message. And for your case, you can't use RX2 as you got a single channel gw.

    Regards, Edi

  • at+set_config=rx2 page 12 of the RAK811-N datasheet
    (all RAK811-N documents are just removed from the rakwireless site !)

    well better is to order a reliable gateway !
    so happy with RPI3 + RAK831 ?
    i hesitate with the IC880A

    thanks for your help, best regards

  • Yes, RAK831/Pi3 runs rock solid at my GWs. If you go this way, I can assist with setting up everything.
    Edit: But don't except too much out of the set LoRa antenna.

  • thanks for your help !

    in fact, i think that all my problems come from that simple GW .. "single channel" and i have several others RF equipment s working on 868MHz .. not on LORA modulation, but same frequency ..


  • Yeah, it's the same situation here: HomeMatic and zWave in My House, zWave and some Babyphones in my neighborhood... The spectrum around 868MHz looks like an Image of the Alps :smile:
    You are very welcome.

  • administrators

    First said sorry to phil31, and thanks to eiten‘s solution of the problem,and then thank you for your use of this product.
    We will use rak's products to the customer to provide technical support, if the customer problems encountered in the use of E-mail to our engineers can try, we will offer solutions in a timely manner.
    Then we will also strengthen the answer to the BBS.

    best regards

Log in to reply

Looks like your connection to RAK Support Center was lost, please wait while we try to reconnect.